Home › Products › Colormaker-acrylmeric-petrol-and-oil-resistant-concrete-sealer

Description:

Shipping

This product is considered a dangerous good for shipping purposes and costs vary depending on your location. Please contact Fingertens for a shipping quote.

Pricing

Acrylmeric Petrol & Oil Resistant Concrete Sealer Clear 20 L = $264.00 gst included.

1L Tint Packs = $79.95 gst included.

Add 1L tint pack to 20L of clear sealer and stir well before use. See colour range below.

Concrete Sealer Colour Range

The colours shown are as near to the actual colours that the computer screen permits. Actual colours vary from batch to batch. Prospective users must satisfy themselves as to the suitability of the coating and colour prior to application. 

Product Features & Benefits

ACRYLMERIC PETROL & OIL RESISTANT CONCRETE SEALER is a high quality, full gloss single pack solvent based acrylic sealer formulated to provide excellent wear, abrasion resistance and general durability to concrete, paving and slate surfaces.

ACRYLMERIC PETROL & OIL RESISTANT CONCRETE SEALER is normally applied as a two coat system for optimum performance and provides excellent washability. It exhibits outstanding stability to UV and provides very good abrasion resistance with multiple coat application.

Nine colour concentrates are available which can be added to the clear concrete sealer to achieve a translucent effect and the product is compatible with 90% of other sealers in this category in the market so can easily be used to revamp existing surfaces.

Applications

• Designed for sealing of domestic pattern and stencil driveways, factory and garage floors, car parks, concrete pavers and slate flooring.
• For garage floors or workshop areas requiring resistance to frequent fuel or oil spills, use ACRYLMERIC PETROL & OIL RESISTANT CONCRETE SEALER.

Benefits

• Adds durability and enhanced visual impact to concrete and masonry surfaces.
• Controls leaching of soluble calcium salts (efflorescence) from cement and concrete surfaces.
• Displays excellent adhesion to properly prepared clean concrete surfaces.
• Unifies the substrate, and acts as a dust suppressant from concrete floors.
• Simplifies cleaning and spillage control procedures.

Surface Preparation

Apply only to a clean, dry surface. Never apply if any moisture is evident on the surface to be coated (this may result in a milky film effect).

Ensure that surfaces are free from any grease, oils and other contaminants and existing coatings. Apply a degreaser to heavily soiled areas, or household grade detergent to lightly soiled areas. Flush residues away with fresh water, whilst scrubbing with a stiff bristle broom.
New concrete must be allowed to age for at least 28 days. Smooth concrete must be acid etched (5-10% Hydrochloric Acid), neutralised with Bicarbonate of Soda, and flushed with fresh water, and then allowed to completely dry before sealer application.

Application

Apply liberally with a long nap roller. Product may also be applied by brush or spray. First coat may be thinned 5-10% with Concrete and Paving Sealer Solvent so as to maximise penetration and minimise bubbling. Allow the coats to dry for 24 hours prior to the addition of any subsequent full strength coat. Avoid application in strong direct sunlight or onto a hot surface so as to maximise coating integrity.
Always allow adequate ventilation during, and immediately after use.

Note: Not to be used when the temperature is less than 10°C, and do not apply to a wet surface.

DRY TIME
Touch dry in 45 minutes @ 25°C.

RECOAT TIME
Minimum recoat time is 12 hours, there is no maximum time.

COVERAGE
Surface type and texture affects the coverage rate. Generally the recommended spreading rate is 6-8 square metres per litre/coat.

CLEAN UP
Clean all equipment thoroughly with CONCRETE AND PAVING SEALER SOLVENT or Solvent CRS

PACKAGING
Available in metal 20L. Reseal the container immediately after use.

FIRST AID
For advice, contact a Poisons information Centre, ph 13 11 26. If swallowed give a glass of water, do NOT induce vomiting. If in eyes wash out immediately with water. If inhaled, remove from contaminated area. Apply artificial respiration if not breathing. If on skin or hair, remove contaminated clothing, and flush affected areas with running water. If irritation occurs seek immediate medical advice.

HEALTH & SAFETY
This product is flammable. Keep away from naked flame. In the event of fire, extinguish with foam or CO2.
Avoid breathing the vapour or spray mist and wear appropriate vapour mask during use. Provide adequate ventilation whilst using in enclosed areas. Avoid contact with the eyes, wear protective eyewear. Avoid contact with the skin. DO NOT SWALLOW. MSDS available upon request.
Sealing of concrete or paving or slate impression concrete etc, may cause surface to become slippery, particularly when wet.

Disclaimer

The technical information and/or application advice given in this publication represents the present state of our knowledge, and is believed to be reliable .Buyers and intended users of Colormaker Industries products should read the TDS carefully and then conduct their own assessment to confirm the suitability of the product, including in conjunction with other products, and the types of surfaces to, and the manner in which, the product will be applied. Colormaker Industries offers no warranty of performance based on the above information either expressed or implied.